Project status¶
The single place that says what works today. Every other page links here instead of repeating it. Update this page whenever an item changes.
As of 2026-11-15. Legend: Done — implemented and checked; In progress — started; Planned — agreed, not started; Open — decision or measurement still missing.
Chain Operator PC → Robot PC → doppelstep¶
This is the current goal: one command from MoveIt reaches a real doppelstep drive. The gripper follows afterwards as a separate project.
| Link | State | Evidence or next step |
|---|---|---|
| Operator PC → Robot PC (DDS) in Docker on one computer | Done | Operator PC container on smx_net; commands arrive and the mock-hardware simulation follows them |
| Operator PC → Robot PC over Wi-Fi, two computers | Planned | Stage 4 |
| Robot PC → doppelstep in simulation (SIL) | Done (2026-11-15) | Six native_sim drives, smoke test PASS, MoveIt from the Operator PC plans and executes (SIL, tutorial) |
| Robot PC → one doppelstep on the bench (ST-LINK VCP) | Planned | Stage 2; the B-G431B-ESC1 is ready |
| Robot PC on the CM4-Duino → DYNAMIXEL bus | Planned | Stage 3 |
| Full arm (six drives) | Planned | Stage 4 |
Components¶
| Component | State | Details |
|---|---|---|
Robot PC image (ROS 2 Jazzy, DynamixelSDK, dynamixel_hardware_interface) |
Done (amd64) | arm64 build planned for the CM4 |
| Simulation with mock hardware, smoke test over DDS | Done | Getting started |
| Robot description from the BCN3D Moveo CAD | Done | Joint limits are placeholders |
Real-hardware ros2_control path |
In progress | hardware:=sil uses it on the virtual bus; hardware:=real refused until Stage 2 |
dynamixel_hardware_interface configuration (ports, IDs, shoulder transmission) |
Done, verified in SIL | Gear and pulley ratios still placeholders until measured |
| doppelstep multi-drive bus behaviour (Fast Sync Read, Sync Read turn-taking) | Done in SIL | X430 emulator 1.1.0; six drives share the virtual bus without help from it (SIL run 10) |
Per-target hardware configuration (sim, sil, hw-pc, hw-cm4) |
Planned | Robot PC on the CM4-Duino |
Deployment files deploy/cm4-duino/ |
Planned | Stage 3 |
| CM4-Duino documentation and vendor archive | Done | CM4-Duino |
| CM4-Duino bring-up (OS, UART, Wi-Fi) | Planned | Stage 3 |
| Wiring of the drives, the bus and the supplies | Done (documented, not built) | Wiring; motor wiring and supply follow the doppelstep hardware documentation |
| Bus interface CM4 ↔ single-wire bus | Planned | Circuit proposed in Wiring; build and measure in Stage 3 |
| doppelstep firmware | Done (v0.3.0) | Verified in simulation and on a B-G431B-ESC1 with a real motor (17HS19-2004S1, 12 V and 24 V); not yet with the arm's motors or with the Robot PC (doppelstep documentation) |
| doppelstep single-wire half-duplex driver | Built, not tested on a board | single-wire.overlay in doppelstep, checked in its CI; board test in Stage 2 |
| Drive ID and baud rate setup | Done (tool) | tools/diagnostics/smx_drive_setup.py, checked on a simulated drive |
| Control Table and timing verified against the Jazzy host sources | Open | Compatibility specification |
| Gripper (MG996R) | Open | Separate project after the chain above works; virtual DYNAMIXEL on ID 7; wiring and requirements documented |
| Motor supply voltage | Agreed | 24 V (D10); first runs at 12 V with current limit |
| Joint limits, motor directions, gear ratios on the real arm | Open | Stage 4 |
| Emergency stop and safe power-up | Open | Needed before the full arm moves |
Decisions¶
The decisions and their status are kept in the integration plan.